www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 8 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 9 59a smd - 4 prepared checked approved ? d a t e 200 6 - 5 - 1 1 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 9 59a s - 4 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 8 ?? history record date spec . no . ?? part no . ??? customer no . modify content ? remark
saw filter hdf 9 59a s - 4 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 8 1 . package dimension unit:mm 2. marking hd f 4 903 2.1 color: black or blue 2.2 959: center frequency(mhz) 3.performance 3.1application low - loss saw filter of cordless system. center frequency:959 mhz 3.2maximum rating operation temperature range - 2 0 to +50 storage temperature range - 40 to +85 dc. permissive voltage 0 v dc. max. maximum input power 5dbm
saw filter hdf 9 59a s - 4 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 8 1.1 electronic characteristics item specification center frequency(fo) 959 mhz insertion loss(db) 1.)95 3 - 96 5 mhz 2.)913 - 918 mhz 3.)936 - 939 m hz 4.)979 - 982 mhz 5.)1000 - 1004 mhz 5 .0 max 40 min 30 min 20 min 40 min ripple deviation (95 3 - 96 5 mhz)(db) 1.5max input/output impedance(nominal) 50 3.4 frequency characteristics 3.5 test circuit
saw filter hdf 9 59a s - 4 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 8 4. environm ental characteristics 4 - 1 temperature cycling subject the device to a low temperature of - 40 for 30 minutes. following by a high temperature of +25 for 5 minutes and a higher temperature of +85 for 30 minutes. then release the device into the room co nditions for 1 to 2 hours prior to the me a surement. it shall meet the specifications in table 1. 4 - 2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 for 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications in table 1. 4 - 3 solderability submerge the device terminals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be covered with new solder. it shall meet the specifications in table 1. 4 - 4 mechanical shock drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in table 1. 4 - 5 vibration subject the device to the vibration for 2 hou r each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the filter shall fulfill the specifications in table 1. 5. remark 5.1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 5.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destruction of the component. please avoid ultrasonic cleaning 5.3 soldering only leads of component ma y be soldered. please avoid soldering another part of component. 6 . packing 6 .1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during transportation and storage. 6 .2 reeling qua ntity 1000 pcs/reel 7??
saw filter hdf 9 59a s - 4 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 8 3000 pcs/reel 13?? 6 .3 taping structure (1) the tape shall be wound around the reel in the direction shown below. (2) label device name user product name quantity lot no. (3) leader p art and vacant position specifications. 7 . tape specifications 7 .1 tensile strength of carrier tape: 4.4n/mm width 7 .2 top cover tape adhesion (see the below figure)
saw filter hdf 9 59a s - 4 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 8 (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g [fig ure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.00 0.30 5.50 0.10 1.75 0.10 4.00 0.10 8.00 0.10 2.00 0.10 ?1.50 ?1.0 0.25 0.25 0.05 1.65 0.10 4.04 0.10 4.10 0.10 [figure 2]
saw filter hdf 9 59a s - 4 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 8 [unit:mm] a b c d e w t r ? 330 1 .0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
